Materials[edit | edit source]
All component materials should be nonhazardous/noncancerous. For tools see: hydroculture DIY tools
- tote (or a 5 gallon bucket) with lid
- air pump, and tubing
- micro-tubing connectors
- basic timer with output plugin (enough to turn on for at least a few minutes 3 times a day)
- substrates: expanded clay, parboiled rice husks (I'm uncertain if growstones being of glass material are safe for aquarium animals)
- high lumen output light bulb: led (lamp or candelabra type may be practical)
Plant and symbiotic animal life[edit | edit source]
- seeds, bulbs, stem cuttings
- chemical fertilizer (Apply 1 teaspoon for the whole system one time only, and this may not be necessary)
- hardy freshwater aquarium animals: goldfish, catfish algae eater, snails or shrimp
- algae wafers, and flakes
Lid[edit | edit source]
Place net-pots upside-down on the tote-lid, and leave 1 inch in diameter in the center vacant for the pex tube to come through. Mark the outline and the center of the tote with a pencil. Use a marker to mark about 1/4in inside the circle. (The lip of the net-pot must rest on the lid) Use a (hand or power) drill, that is the same outer diameter as the pex pipe, to make a hole in the center of the lid. Cut holes out for the net-pots. (As mentioned before, make sure the hole is smaller than the outer diameter of the net-pot, so the net-pot won't fall through.)
Airlift pump[edit | edit source]
The benefits using an air-pump is: that it is convenient to buy, that it is not allowed to be underwater causing an electrical hazard and that not a lot of water pressure is required in this system. The aquarium pump will sit higher than and outside the aquaponics unit, and it will serve the function of an airlift pump.
An airlift can be made with microtubing and a T connector. First, connect the middle part of the T to the air supply in. Then, connect a short length of microtubing to one end of the T, and the fountain out to the opposite end. A micro barb coupling can be inserted on the fountain end of the microtubing to allow a narrow opening to make the water sputter further. This can also be used to connect the fountain end of the microtubing to the top of the tote lid.
The water input should be lower than the air input, and a weight may be necessary. If done properly, once the tote is filled with water, the air will push the water up to spill on the top of the tote-lid.
Timer[edit | edit source]
The timer only needs to be on to run the air pump enough to wet the substrate material, and needs to turn on a few times a day, at minimum for plant health. This eliminates the need for buying an expensive timer (required for a true aeroponic system), or having to build your own through dc circuitry. The substrate material does enough to keep the plant's roots moist between waterings. However, the timer should turn on often, or be left on without the timer, to aerate the fish and the tank and for improved plant growth. (a mechanical timer with settings for 30 or 15 minutes on/off will work) Plants need about 6 hours a day of darkness. Water falling back towards the tote aerates the water. Hook the timer to both the led (or fluorescent) light and air pump. Choose a bright light, and put the system near a window. (Its ok to have both turn on at the same time, allow the timer to turn on less often at night)
Final steps[edit | edit source]
Wipe down inside of tote, cleaning up fragments. Add water and fertilizer solution (see above) to the tote. Use de-chlorinated water or let system run for a few minutes beforehand to de-chlorinate. Chlorine dissipates on contact with air, and chloramine takes longer to dissipate. Set in lid and net-pots. 1 net pot can be left out to let light in for the fish, but not too much light should be let in, for plant root health. Fill the net-pots halfway with substrate material. Add bulbs, stem cuttings or seeds. (Don't use plants dangerous to fish). Let plant stems grow before adding the rest of the material. Rockwool is not aerated enough, so it is ideal for balling around small seeds or layering around a stem cutting. Most material needs to be a porous. Coco-peat helps prevent fungus formation. Add goldfish, and feed them daily. Goldfish seem to graze on algae. Algae eaters, shrimp and snails are optional for cleaning up algae. The fish in this type of aquaponic system are hardier than plants. Once the fish are established they do the work of keeping the fertilizer level stable.