How To Build a Pinewood Derby Car/Glossary

From Wikibooks, open books for an open world
< How To Build a Pinewood Derby Car
Jump to: navigation, search

Derby icon.svg

Table of Contents
edit
Alignment
The process of aligning the wheel vertically (camber angle) and parallel to the direction of travel (toe and steer angles).
Axle Slot
One of two slots cut in the stock BSA kit block.
Beveling
tapering the axle to reduce the contact area between the axle head and the outer wheel hub.
Balancing
Wheel modification to achieve an equivalent mass distributed about the hub.
Block
The 7 x 1-3/4 x 1-1/4 pine block.
Bore polishing
Polishing the inner surface of the hub to reduce friction between the wheel and axle.
BSA
Boy Scouts of America.
Coning
Modification of the inside wheel hub to reduce hub-to-body friction.
Center Rail
On wood tracks, a lane guide that is approximately 1/4" inch tall and 1-5/8" wide that the car straddles to keep it on the track.
Deburring
Axles are essentially one-inch nails that have two burrs under the head from the stamping process. A typical axle treatment consists of removing these burrs followed by sanding and polishing.
Dominant Wheel
The front wheel that touches when the car is on a flat surface. In a raised front wheel configuration, this is the wheel that is not raised.
Extended Wheelbase
The largest distance possible between the axles such that the wheels do net extend past the end of the block: 5-3/4" with the axle holes 5/8" from the end of the block.
Graphite
A form of carbon that is found in pencil lead. It is one of the favored dry lubricants
Grooving
Notching of axles to reduce the contact area and thus the friction between the axle and the wheel.
H Tread
A wheel modification in which the tread is cut with a "H" cross-section to allow contact with the track surface on the inner and outer parts of the tread only.
Kit
The Official BSA "Grand Prix Pinewood Derby Kit" with block, 4 axles, 4 wheels and instructions.
Krytox
A liquid synthetic lubricant (MSDS).[1], Krytox oils and greases are perfluoropolyether (PFPE) synththetic lubricants made by DuPont
Light Wheels
Wheels that have been reduced in mass, typically by removal of material from the inner side of the wheel.
Matched Wheels
Wheels taken from the same mold number.
Mold
The plastic injection mold for pinewood derby wheels.
Mold Number
The number on the inside of a wheel, indicating the injection mold.
Moly
Molybdenum disulfide lubricant.
Molybdenum disulfide
Molybdenum disulfide is a dry lubricant similar to graphite.
Nickel plating
Nickel plated axles can be polished to a smoother finish than stock zinc BSA axles.
Notching or Grooving
Axles can be notched or grooved to reduce the contact area and thus the friction between the axle and the wheel.
Nyoil
A liquid synthetic lubricant (MSDS).
Pinewood derby car "outlaw" wheels
Outlaw Wheels
Thin wheels machined from a high-performance polymer such as delrin that are typically allowed only in open class races.
Oversize Axles
Oversize axle (e.g. 0.091 diameter) axles can reduce wheel wobble. Official BSA axles are 0.087 inch in diameter.
Rail Riding
Adjustment of the dominant front wheel alignment to induce a slight steer toward the track center rail to cause the car to hug the rail as it goes down the track.
Raised Wheel
One wheel (typically front) raised approximately 1/16 inch on the car body. This wheel is not in constant contact with the track and thus contributes less to the rotational inertia.
Silicone
A polysiloxanes organic/inorganic polymer lubricant.
Nickel-plated speed axle
Speed Axles
Nickel-plated aftermarket axles.
Teflon
The trade name for polytetrafluoroethylene (PTFE) polymer. Powdered Teflon is a common Derby car lubricant.
V Tread
A wheel modification in which the tread is cut with a "V" cross-section to allow a single radial point of contact with the track surface.
Wheelbase
The spacing between the front and rear wheels from wheel center to wheel center. The standard pinewood derby wheelbase is about 4.5 inches and the extended wheelbase is 5.75 inches with the wheels 5/8 inch from the end of the 7 inch block.