[From gmpf.de retrieved via google cache]
Stereoscopy (or stereo for short) is a way of running 3D applications in true stereo so when viewed correctly appear to have depth.
What is needed for Stereo[edit | edit source]
The following are required to use stereo with a NVIDIA graphics card, other cards also support stereo such as the ATi and should have similar requirements and similar steps to get it going.
- a Nvidia Quadro card with QuadBuffered Stereo support (all current ones except NVS range). Note that NVIDIA mention using page flipped stereo with normal GeForce cards using a special driver, but this driver is for Windows only.
- Some type of Stereo display, for example
- High refresh rate (100-120hz) screen such as a CRT monitor or DLP projector and some shutter glasses
- an autostereo screen
- two projectors with 100% overlap with different polarising filters and polarised glasses.
- a stereo headset with one screen for each eye
- In some cases a converter to provide a 3pin stereo DIN output if your card does not have one.
Basic Setup[edit | edit source]
To configure the type of stereo you will use, you will need to set the "Stereo" option. The format of this option is:
Option "Stereo" "integer"
and its values can be:
- 1 - DDC stereo, for signalling on the " DDC line
- 2 - Blue line stereo, signalling via a varying length blue line at the bottom of the screen (This option can be used, it seems, with the " Stereo Graphics StereoEnabler
- 3 - On-board stereo output with 3-pin connector for direct connection to shutter glasses.
- 4 - TwinView stereo (passive, one eye per screen, typically used with two projectors setup with polarising filters in front of them)
Options 1 and 2 require a converter box added to the video card's video output to convert the video signal into a form that the shutter glasses can understand, these options are useful if your card doesn't have 3-pin mini-din output. For example, the Elsa Revelator shutterglasses (Option "Stereo" 1) comes with a adapter that connects to the VGA card at one side and to the monitor cable and a 3-pin mini-DIN socket for the cable of the glasses (or the emitter) to the other side.
For active stereo you will need a high refresh rate, the default one (typically 85hz) will be too low for comfortable viewing of stereo. To do this, you will need to get the following specifications of your monitor, in particular:
- Vertical Sync range (vsync)
- Horizontal Sync range (hsync)
- Maxiumum Pixel Clock (pclk)
Use these values to configure the HorizSync and VertRefresh configuration settings and if we are using TwinView the SecondMonitorHorizSync and SecondMonitorVertRefresh Options in your XF86Config-4 file. Once we have set these up we are ready to create our custom modeline(s). To do this we can use the gtf utility, for example to create a ModeLine for 1024×768@120 Hz we do the following:
gtf 1024 768 120 # 1024x768 @ 120.00 Hz (GTF) hsync: 98.76 kHz; pclk: 139.05 MHz Modeline "1024x768_120.00" 139.05 1024 1104 1216 1408 768 769 772 823 -HSync +Vsync
If for example your monitor has a horizontal sync range of 50-121 kHz, this would be below the maximum specification supported by the monitor, we can increase the refresh rate until we reach the maximum specifications so that we get a better flicker free image; e.g.
gtf 1024 768 144 # 1024x768 @ 144.00 Hz (GTF) hsync: 120.24 kHz; pclk: 169.30 MHz Modeline "1024x768_144.00" 169.30 1024 1104 1216 1408 768 769 772 835 -HSync +Vsync
alternatively we could increase the resolution keeping the refresh rate the same:
gtf 1152 864 120 # 1152x864 @ 120.00 Hz (GTF) hsync: 111.12 kHz; pclk: 176.01 MHz Modeline "1152x864_120.00" 176.01 1152 1240 1368 1584 864 865 868 926 -HSync +Vsync
When you have finished put the line into your XF86Config-4 file, and update the Modes config option of your Display Section e.g.
Subsection "Display" Depth 24 Modes "1152x864_120.00" EndSubsection
or if you're using TwinView...
Option "MetaModes" "1152x864_120.00,1152x864_120.00"
in your screen section. Once you have set this all up logout and restart the X server with Crtl-Alt-Backspace. You should now be running at your new refresh rate with stereo enabled. There are several ways to check the refresh rate:
- On screen dialogs on your monitor may tell you
- The xvidtune command
- The xrandr command
gcc -lglut -lGL -lm -lGLU -lX11 -lXmu -lXi -lXext -L/usr/X11R6/lib pulsar.c -o pulsar
then run it
and if it works your done.
Advanced Setup[edit | edit source]
TwinView[edit | edit source]
There are no extra configuration options needed to setup [NVidia/TwinView] to use stereo, however a number of conditions must be met for this to work
- Both monitors must be running at with the same mode (see "ENSURING IDENTICAL MODE TIMINGS" section of the " README for details.
- You are not using version 66.29 of the drivers as this feature appears to be broken that version, it is fixed in version 71.74
- Neither monitor is detected as a DFP.
Related Options[edit | edit source]
- "AllowDFPStereo" By default stereo is disabled for displays detected as Digital Flatpanels (DFPs i.e. LCD monitors), setting this to yes re-enables it.
Hardware suppliers[edit | edit source]
Related Links[edit | edit source]
- Software-based Genlock for Active Stereo NVIDIA Cards - Cheaper alternative to "G" cards?
- VRizer - Run non stereo enabled applications in stereo